Solar, wind, and geothermal energy sources are all renewable. They derive their energy from natural processes that replenish themselves over time.
There are a few things that are true about solar, wind, and geothermal energy.
Renewable energy sources include solar, wind, and geothermal power. They get their energy from natural processes that grow back eventually. Solar energy comes from the sun, wind energy comes from the movement of air, and geothermal energy comes from heat inside the Earth.
They are all environmentally friendly which means that it doesn't harm the environment. Solar, wind, and geothermal energy sources are better for the environment than fossil fuels. They release very little greenhouse gases when they are being used, which helps to prevent climate change and make the air cleaner.
Learn more on geothermal on brainly.com/question/1197584
#SPJ6
Answer:
.
.
.
.
.
.
hope it helps...
b. at high altitudes
c. near the poles
d. in the middle of a continent
I think its a
I hope its right if it is sub to me Bearonic
The greatest acceleration that the truck can have before the toolbox slides out can be calculated by understanding the balance between the inertia force experienced by the toolbox due to acceleration (F = ma) and the maximum static friction force (fs(max) = μsN) opposing this motion. The truck can accelerate up to the point at which these two forces are equal.
The question relates to a concept in Physics known as Friction. In this scenario, the toolbox on the truck experiences static friction which keeps it from sliding. The maximum force of static friction can be calculated using the equation fs(max) = μsN, where μs is the coefficient of static friction and N is the normal force. In this case, μs is given as 0.300 and the normal force N equals the weight of the toolbox. The truck can accelerate up to the point where the frictional force equals the force caused by acceleration, which is calculated using the equation F = ma, where m is mass and a is acceleration.
When the truck accelerates, an inertia force acts on the toolbox in the opposite direction. This inertia force, F = ma, should not exceed the maximum static friction force, fs(max), otherwise, the toolbox will slide. Hence, with given values of static friction coefficient and mass of the toolbox, the greatest acceleration of the truck to prevent slipping can be calculated by equating the frictional force and inertia force.
#SPJ12
The greatest acceleration that the truck can have before the toolbox slides out is 5.00 m/s².
The greatest acceleration that the truck can have before the toolbox slides out can be found by comparing the force of static friction to the force pushing the toolbox forward. In this case, the force of static friction must be equal to or greater than the force pushing the toolbox, which is the product of the mass of the toolbox and its acceleration. Given the coefficient of static friction of 0.300, the maximum force of static friction can be calculated. Using the equation fs <= μsN, where fs is the force of static friction, μs is the coefficient of static friction, and N is the normal force, we can substitute the values and solve for the maximum force of static friction which is 196 N. The maximum force of static friction is equal to the product of the mass of the toolbox and its acceleration, which gives us the equation fs = max = (50.0 kg)(5.00 m/s²) = 250 N. Therefore, the greatest acceleration that the truck can have before the toolbox slides out is 5.00 m/s².
#SPJ11
The approximate horizontal component of the initial velocity is 12.3 m/s
When an object is thrown at an angle from the horizontal direction, the object is said to be in projectile motion. The object which follows the projectile motion.
Given is Ronnie kicks a playground ball with an initial velocity of 16 m/s at an angle of 40° relative to the ground.
The horizontal component of the projectile is
Vx= V cosθ
Substitute the values, we get
Vx = 16 cos(40) =
Vx =12.3 m/s
Thus, approximate horizontal component of the initial velocity is 12.3 m/s.
Learn more about projectile.
#SPJ5
The buoyancy of an object depends on its density relative to the density of the fluid it's placed in, typically water in everyday scenarios. When an object is placed in a fluid (like water), it will float if its average density is less than that of the fluid. In other words, if the object is less dense than the fluid, it will float.
In this case, both pieces of wood have the same density of 0.90 grams per milliliter (g/ml), which is less dense than water. Therefore, both the 1-pound piece of wood and the 10-pound piece of wood will float in water.
However, it's important to note that the buoyant force acting on these objects will be the same for a given volume of wood because they have the same density.
The 10-pound piece of wood will displace more water (have a larger volume) to support its weight, while the 1-pound piece of wood will displace less water (have a smaller volume) to support its weight. The 10-pound piece of wood will have more of its volume submerged compared to the 1-pound piece due to the weight difference, but both will float.